From Glomation Product Support

Product: GESBC-9G20i

Documentation

GESBC-9G20i User's Manual.


Pre-built Binary Images

Pre-compiled boot strap code for standard 32MB SDRAM board.
Pre-compiled boot strap code for optional 64MB SDRAM board.
Pre-compiled U-Boot image for standard 32MB SDRAM board.
Pre-compiled U-Boot image for optional 64MB SDRAM board.
Pre-compiled Linux 2.6.35.9 kernel image.
Embedded Linux file system JFFS2 image(OABI) based on Emdebian Crush.
Pre-compiled WIFI (VNT-6656) driver module for kernel 2.6.35.9.
Pre-compiled character LCD display driver module for kernel 2.6.35.9.


Source Code

Kernel configuration file for kernel 2.6.35.9.
Kernel source patch file for kernel 2.6.35.9.
GESBC-9G20i bootstrap code source package


Use the On-Chip 4 Channel 10bit ADC

The ADC driver for the AT91SAM9G20 on-chip ADC exposes the user space interface via sysfs. Below is a simple command line example reading the on-chip ADC,

 echo "1" > /sys/class/misc/adc/ch0_enable 
 cat /sys/class/misc/adc/ch0_value

The ADC input range is 0 ~ 3.3V. The resolution is 10bits.


Control The Digital Output

There are 6 open collector output ports on the GESBC-9G20i. They are connected as following,

GPIO Pin PB12 PB13 PB16 PB17 PB18 PB19
Output Pin on J8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14

The GPIO driver uses sysfs to interface with user space programs. The control file structure is,

 #: ls/sys/class/gpio
 export       gpiochip0    gpiochip32   gpiochip96
 gpiochip128  gpiochip64   unexport

The GPIO pins are grouped into 3 groups on the AT91SAM9G20 processor, PIO-A, PIO-B, PIO-C. The device driver maps pins of each group into GPIO chips and each GPIO pin was assigned a port number. The PIO-A starts from port number 32, the PIO-B starts from port number 64, and the PIO-C starts from 96. To calculate the port number of a specific pin just simply add the pin number in its group to the group base number. For example the PB12 is mapped at port number 64 + 12 = 76.

The GPIO output must be exported first before it can be used. The direction also must be set as output as shown in the following example,

 echo "76" > /sys/class/gpio/export
 echo "out" > /sys/class/gpio/gpio76/direction
 echo "1" > /sys/class/gpio/gpio76/value
 sleep 3
 echo "0" > /sys/class/gpio/gpio76/value

Please note the GPIO numbering scheme has changed from kernel version 3.6.*. The PIO-A starts from 0 instead of 32 for newer kernels.


Read the Digital Input Ports

The GESBC-9G20i has 8 protected digital input ports configured as following,

GPIO Pin PC16 PC17 PC18 PC19 PB20 PB21 PB22 PB23
Input Pin on J8 Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8

The following example demonstrates the basic operation of reading the first digital input port on terminal block J8 on the GESBC-9G20i,

 echo "112" > /sys/class/gpio/export
 echo "in" > /sys/class/gpio/gpio112/direction
 cat < /sys/class/gpio/gpio112/value

Please note the port number and direction only needs to be exported and set once.


Sample Programs

Sample C program to control digital output and read digital input on GESBC-9G20i.

Sample C program to display messages on a 4 x 20 character LCD display connected to a GESBC-9G20i.

Sample RS-485 communication C program to send data through RS-485 port.

Retrieved from http://glomationinc.com/SupportWiki/index.php?n=Product.GESBC-9G20i
Page last modified on July 26, 2016, at 04:48 PM